R.M.S Titanic Anchor Replica Scale 1:17<\/h3>\n\n\n\n![\"\"](\"https:\/\/propdesign.se\/wp-content\/uploads\/2021\/07\/20210712_135004771_iOS_2-1024x453.jpg\")
<\/figure><\/div>\n\n\n\nThis is a 3d-printed, framed replica of R.M.S Titanic center anchor in scale 1:17. It consists of 12 parts and is fully movable according to specifications. The original anchor made during the construction of Titanic had a total weight of 15,5 metric tons and was the largest anchor in the world at the time (except for the R.M.S Olympic’s anchor which was made before Titanic with the same specs).<\/p>\n\n\n\n
This framed version of the anchor will be made in only 5 copies and sold to collectors around the world.<\/p>\n\n\n\n
\n\n\n\nComing up next<\/h2>\n\n\n\nMandalorian (Tv-show) – Hero Helmet, full scale.<\/h3>\n\n\n\n![\"\"](\"https:\/\/propdesign.se\/wp-content\/uploads\/2021\/07\/Helmet-1024x489.jpg\")
<\/figure>\n\n\n\nI am a Star Wars fan so i liked the Mandalorian series a lot, and i can’t wait to see more of it, and on top of that i like to 3d-print stuff and when i found a full scale 3d-printable helmet i was sold, i got to print this one. This will fit good to my Star Wars collection and specially with my ”The Child” statue. I will make three helmets, one for me and two for my friends. This project will begin when all the anchors from my ongoing project are done and shipped.<\/p>\n\n\n\n
\n\n\n\nFinished projects<\/h2>\n\n\n\nSea of Thieves (Xbox game) – Replica of Chalice of ancient fortune, full scale.<\/h3>\n\n\n\n![\"\"](\"https:\/\/propdesign.se\/wp-content\/uploads\/2021\/07\/20210712_124741405_iOS-e1627476967573-1024x499.jpg\")
<\/figure><\/div>\n\n\n\nThere is one game i play, and i play a lot, thats Sea of thieves. The Chalice of Ancient Fortune is a type of Athena’s Treasure in Sea of Thieves. Chalices of Ancient Fortune can commonly be dug up from X Marks the Spot Maps or found inside Collector’s Chests during Athena’s Fortune Voyages, Athena’s Run Voyages or Athena’s Fortune Emissary Quests. The idea were that i will print this and drink from but then you will have to cast since resin is toxic and i can’t use it for food or drinks. However, I did not find anyone that could help me with casting so i just 3d-printed it as an ornament. It might be casting it in the future.<\/p>\n\n\n\n
Game of thrones (Tv-show) – Framed logo<\/h3>\n\n\n\n![\"\"](\"https:\/\/propdesign.se\/wp-content\/uploads\/2021\/07\/20210714_125145590_iOS_2-1024x568.jpg\")
<\/figure>\n\n\n\nI have a couple of replicas from the show: Dragon eggs, The Iron Throne, Jon Snow’s Sword, Game of thrones collectors Blu-ray box, so i wanted something that hangs over all the stuff that i have collected so i made this framed logo.<\/p>\n\n\n\n
Star Wars (Movie) – Luke’s Lightsaber (first attempt), full scale.<\/h3>\n\n\n\n![\"\"](\"https:\/\/propdesign.se\/wp-content\/uploads\/2021\/07\/20210712_125156459_iOS-1024x747.jpg\")
<\/figure><\/div>\n\n\n\nI have been fascinated about the light sabers from Star Wars a long time, and i have for a long time wanted a replica of Luke’s light saber including electronics and soundboard, I bought a replica from Park Sabers in 2016, assembled it right away and for a long time it was just an empty hilt. It took me about three years before i started with the internals. All of the internals was modeled in a 3d-program and 3d-printed on an FDM printer. All of the electronics was ordered from the custom saber shop.<\/p>\n\n\n\n
Batman Begins (Movie) – Batarang replica, full scale.<\/h3>\n\n\n\n![\"\"](\"https:\/\/propdesign.se\/wp-content\/uploads\/2021\/07\/20210728_182211069_iOS-1024x715.jpg\")
<\/figure><\/div>\n\n\n\nThe Batman logo is very cool and i would like to have one on my wall, so i made one! This made from 5 mm steel. I first made a 3d model that i printed and used as a template, I then cut it out from a 5 mm thick sheet metal plate. Then i used air tools and a Dremel to refine the shape and looks.<\/p>\n","protected":false},"excerpt":{"rendered":"
Here you can find a collection of my projects. Click on the topic of each project to read more about it. (Coming soon) Ongoing projects R.M.S Titanic Anchor Replica Scale 1:17 This is a 3d-printed, framed replica of R.M.S Titanic center anchor in scale 1:17. It consists of 12 parts and is fully movable according … <\/p>\n
<\/figure><\/div>\n\n\n\nThis is a 3d-printed, framed replica of R.M.S Titanic center anchor in scale 1:17. It consists of 12 parts and is fully movable according to specifications. The original anchor made during the construction of Titanic had a total weight of 15,5 metric tons and was the largest anchor in the world at the time (except for the R.M.S Olympic’s anchor which was made before Titanic with the same specs).<\/p>\n\n\n\n
This framed version of the anchor will be made in only 5 copies and sold to collectors around the world.<\/p>\n\n\n\n
\n\n\n\n
Coming up next<\/h2>\n\n\n\nMandalorian (Tv-show) – Hero Helmet, full scale.<\/h3>\n\n\n\n<\/figure>\n\n\n\nI am a Star Wars fan so i liked the Mandalorian series a lot, and i can’t wait to see more of it, and on top of that i like to 3d-print stuff and when i found a full scale 3d-printable helmet i was sold, i got to print this one. This will fit good to my Star Wars collection and specially with my ”The Child” statue. I will make three helmets, one for me and two for my friends. This project will begin when all the anchors from my ongoing project are done and shipped.<\/p>\n\n\n\n
\n\n\n\nFinished projects<\/h2>\n\n\n\nSea of Thieves (Xbox game) – Replica of Chalice of ancient fortune, full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nThere is one game i play, and i play a lot, thats Sea of thieves. The Chalice of Ancient Fortune is a type of Athena’s Treasure in Sea of Thieves. Chalices of Ancient Fortune can commonly be dug up from X Marks the Spot Maps or found inside Collector’s Chests during Athena’s Fortune Voyages, Athena’s Run Voyages or Athena’s Fortune Emissary Quests. The idea were that i will print this and drink from but then you will have to cast since resin is toxic and i can’t use it for food or drinks. However, I did not find anyone that could help me with casting so i just 3d-printed it as an ornament. It might be casting it in the future.<\/p>\n\n\n\n
Game of thrones (Tv-show) – Framed logo<\/h3>\n\n\n\n<\/figure>\n\n\n\nI have a couple of replicas from the show: Dragon eggs, The Iron Throne, Jon Snow’s Sword, Game of thrones collectors Blu-ray box, so i wanted something that hangs over all the stuff that i have collected so i made this framed logo.<\/p>\n\n\n\n
Star Wars (Movie) – Luke’s Lightsaber (first attempt), full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nI have been fascinated about the light sabers from Star Wars a long time, and i have for a long time wanted a replica of Luke’s light saber including electronics and soundboard, I bought a replica from Park Sabers in 2016, assembled it right away and for a long time it was just an empty hilt. It took me about three years before i started with the internals. All of the internals was modeled in a 3d-program and 3d-printed on an FDM printer. All of the electronics was ordered from the custom saber shop.<\/p>\n\n\n\n
Batman Begins (Movie) – Batarang replica, full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nThe Batman logo is very cool and i would like to have one on my wall, so i made one! This made from 5 mm steel. I first made a 3d model that i printed and used as a template, I then cut it out from a 5 mm thick sheet metal plate. Then i used air tools and a Dremel to refine the shape and looks.<\/p>\n","protected":false},"excerpt":{"rendered":"
Here you can find a collection of my projects. Click on the topic of each project to read more about it. (Coming soon) Ongoing projects R.M.S Titanic Anchor Replica Scale 1:17 This is a 3d-printed, framed replica of R.M.S Titanic center anchor in scale 1:17. It consists of 12 parts and is fully movable according … <\/p>\n
<\/figure>\n\n\n\nI am a Star Wars fan so i liked the Mandalorian series a lot, and i can’t wait to see more of it, and on top of that i like to 3d-print stuff and when i found a full scale 3d-printable helmet i was sold, i got to print this one. This will fit good to my Star Wars collection and specially with my ”The Child” statue. I will make three helmets, one for me and two for my friends. This project will begin when all the anchors from my ongoing project are done and shipped.<\/p>\n\n\n\n
\n\n\n\n
Finished projects<\/h2>\n\n\n\nSea of Thieves (Xbox game) – Replica of Chalice of ancient fortune, full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nThere is one game i play, and i play a lot, thats Sea of thieves. The Chalice of Ancient Fortune is a type of Athena’s Treasure in Sea of Thieves. Chalices of Ancient Fortune can commonly be dug up from X Marks the Spot Maps or found inside Collector’s Chests during Athena’s Fortune Voyages, Athena’s Run Voyages or Athena’s Fortune Emissary Quests. The idea were that i will print this and drink from but then you will have to cast since resin is toxic and i can’t use it for food or drinks. However, I did not find anyone that could help me with casting so i just 3d-printed it as an ornament. It might be casting it in the future.<\/p>\n\n\n\n
Game of thrones (Tv-show) – Framed logo<\/h3>\n\n\n\n<\/figure>\n\n\n\nI have a couple of replicas from the show: Dragon eggs, The Iron Throne, Jon Snow’s Sword, Game of thrones collectors Blu-ray box, so i wanted something that hangs over all the stuff that i have collected so i made this framed logo.<\/p>\n\n\n\n
Star Wars (Movie) – Luke’s Lightsaber (first attempt), full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nI have been fascinated about the light sabers from Star Wars a long time, and i have for a long time wanted a replica of Luke’s light saber including electronics and soundboard, I bought a replica from Park Sabers in 2016, assembled it right away and for a long time it was just an empty hilt. It took me about three years before i started with the internals. All of the internals was modeled in a 3d-program and 3d-printed on an FDM printer. All of the electronics was ordered from the custom saber shop.<\/p>\n\n\n\n
Batman Begins (Movie) – Batarang replica, full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nThe Batman logo is very cool and i would like to have one on my wall, so i made one! This made from 5 mm steel. I first made a 3d model that i printed and used as a template, I then cut it out from a 5 mm thick sheet metal plate. Then i used air tools and a Dremel to refine the shape and looks.<\/p>\n","protected":false},"excerpt":{"rendered":"
Here you can find a collection of my projects. Click on the topic of each project to read more about it. (Coming soon) Ongoing projects R.M.S Titanic Anchor Replica Scale 1:17 This is a 3d-printed, framed replica of R.M.S Titanic center anchor in scale 1:17. It consists of 12 parts and is fully movable according … <\/p>\n
<\/figure><\/div>\n\n\n\nThere is one game i play, and i play a lot, thats Sea of thieves. The Chalice of Ancient Fortune is a type of Athena’s Treasure in Sea of Thieves. Chalices of Ancient Fortune can commonly be dug up from X Marks the Spot Maps or found inside Collector’s Chests during Athena’s Fortune Voyages, Athena’s Run Voyages or Athena’s Fortune Emissary Quests. The idea were that i will print this and drink from but then you will have to cast since resin is toxic and i can’t use it for food or drinks. However, I did not find anyone that could help me with casting so i just 3d-printed it as an ornament. It might be casting it in the future.<\/p>\n\n\n\n
Game of thrones (Tv-show) – Framed logo<\/h3>\n\n\n\n<\/figure>\n\n\n\nI have a couple of replicas from the show: Dragon eggs, The Iron Throne, Jon Snow’s Sword, Game of thrones collectors Blu-ray box, so i wanted something that hangs over all the stuff that i have collected so i made this framed logo.<\/p>\n\n\n\n
Star Wars (Movie) – Luke’s Lightsaber (first attempt), full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nI have been fascinated about the light sabers from Star Wars a long time, and i have for a long time wanted a replica of Luke’s light saber including electronics and soundboard, I bought a replica from Park Sabers in 2016, assembled it right away and for a long time it was just an empty hilt. It took me about three years before i started with the internals. All of the internals was modeled in a 3d-program and 3d-printed on an FDM printer. All of the electronics was ordered from the custom saber shop.<\/p>\n\n\n\n
Batman Begins (Movie) – Batarang replica, full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nThe Batman logo is very cool and i would like to have one on my wall, so i made one! This made from 5 mm steel. I first made a 3d model that i printed and used as a template, I then cut it out from a 5 mm thick sheet metal plate. Then i used air tools and a Dremel to refine the shape and looks.<\/p>\n","protected":false},"excerpt":{"rendered":"
Here you can find a collection of my projects. Click on the topic of each project to read more about it. (Coming soon) Ongoing projects R.M.S Titanic Anchor Replica Scale 1:17 This is a 3d-printed, framed replica of R.M.S Titanic center anchor in scale 1:17. It consists of 12 parts and is fully movable according … <\/p>\n
<\/figure>\n\n\n\nI have a couple of replicas from the show: Dragon eggs, The Iron Throne, Jon Snow’s Sword, Game of thrones collectors Blu-ray box, so i wanted something that hangs over all the stuff that i have collected so i made this framed logo.<\/p>\n\n\n\n
Star Wars (Movie) – Luke’s Lightsaber (first attempt), full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nI have been fascinated about the light sabers from Star Wars a long time, and i have for a long time wanted a replica of Luke’s light saber including electronics and soundboard, I bought a replica from Park Sabers in 2016, assembled it right away and for a long time it was just an empty hilt. It took me about three years before i started with the internals. All of the internals was modeled in a 3d-program and 3d-printed on an FDM printer. All of the electronics was ordered from the custom saber shop.<\/p>\n\n\n\n
Batman Begins (Movie) – Batarang replica, full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nThe Batman logo is very cool and i would like to have one on my wall, so i made one! This made from 5 mm steel. I first made a 3d model that i printed and used as a template, I then cut it out from a 5 mm thick sheet metal plate. Then i used air tools and a Dremel to refine the shape and looks.<\/p>\n","protected":false},"excerpt":{"rendered":"
Here you can find a collection of my projects. Click on the topic of each project to read more about it. (Coming soon) Ongoing projects R.M.S Titanic Anchor Replica Scale 1:17 This is a 3d-printed, framed replica of R.M.S Titanic center anchor in scale 1:17. It consists of 12 parts and is fully movable according … <\/p>\n
<\/figure><\/div>\n\n\n\nI have been fascinated about the light sabers from Star Wars a long time, and i have for a long time wanted a replica of Luke’s light saber including electronics and soundboard, I bought a replica from Park Sabers in 2016, assembled it right away and for a long time it was just an empty hilt. It took me about three years before i started with the internals. All of the internals was modeled in a 3d-program and 3d-printed on an FDM printer. All of the electronics was ordered from the custom saber shop.<\/p>\n\n\n\n
Batman Begins (Movie) – Batarang replica, full scale.<\/h3>\n\n\n\n<\/figure><\/div>\n\n\n\nThe Batman logo is very cool and i would like to have one on my wall, so i made one! This made from 5 mm steel. I first made a 3d model that i printed and used as a template, I then cut it out from a 5 mm thick sheet metal plate. Then i used air tools and a Dremel to refine the shape and looks.<\/p>\n","protected":false},"excerpt":{"rendered":"
Here you can find a collection of my projects. Click on the topic of each project to read more about it. (Coming soon) Ongoing projects R.M.S Titanic Anchor Replica Scale 1:17 This is a 3d-printed, framed replica of R.M.S Titanic center anchor in scale 1:17. It consists of 12 parts and is fully movable according … <\/p>\n
<\/figure><\/div>\n\n\n\nThe Batman logo is very cool and i would like to have one on my wall, so i made one! This made from 5 mm steel. I first made a 3d model that i printed and used as a template, I then cut it out from a 5 mm thick sheet metal plate. Then i used air tools and a Dremel to refine the shape and looks.<\/p>\n","protected":false},"excerpt":{"rendered":"
Here you can find a collection of my projects. Click on the topic of each project to read more about it. (Coming soon) Ongoing projects R.M.S Titanic Anchor Replica Scale 1:17 This is a 3d-printed, framed replica of R.M.S Titanic center anchor in scale 1:17. It consists of 12 parts and is fully movable according … <\/p>\n